Plumbing Basics: What You Need for Installing a Bathtub
Plumbing Basics: What You Need for Installing a Bathtub
Blog Article
How do you actually feel in regards to Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't specifically brain surgery, however it does require strong plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably challenging task. If the old bathtub is conveniently accessible, the task can move immediately; if you need to open a wall surface to remove the old bathtub and position the new bathtub, the job is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly need a helper to leave the old bathtub and embeded in the new one. See to it you have actually qualified yourself for the job and fit trying it. Instead of employing a specialist to take over a halfway-completed project, it is far better to think about utilizing one before you start. Possibilities are you may require an expert plumber to make tube connections.
This write-up will aid you mount a new tub in your restroom if you have currently gotten a new bathtub as well as don't need to transform the arrangement of your previous supply of water pipelines.
Your tools and also product checklist should make up the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the water system. After doing so, switch on the taps to drain any water remaining in the system. The procedure of getting rid of the existing taps can be fairly troublesome due to the limited gain access to that is typically the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have been eliminated, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning during this procedure. When the taps have been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washers remain in location between the tap and also the sink. Secure the tap in place with the manufacturer offered backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap ports. The previous kind needs to be connected to the tap ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Bath tub
Making use of both wood boards under its feet, put the bathtub in the required placement. The wood boards are handy in equally spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little points.
The following goal is to make certain that the tub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the bath tub until the level reads level.
To mount taps, fit the bottom of the furthest flexible tap connector to the proper supply pipe by making a compression sign up with; then do the very same for the various other faucet.
Switch on the water system as well as check all joints and new pipework for leaks and tighten them if essential. Fill up the bathtub as well as also inspect the overflow electrical outlet as well as the normal electrical outlet for leakages.
Ultimately, fix the bathroom paneling as defined in the manufacturer's user's manual. Tiling and also securing around the tub ought to wait until the bath tub has actually been utilized a minimum of once as this will certainly settle it into its last setting.
Getting ready for the Setup
Firstly, the supporting frame supplied with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is important to see to it that if the tap includes a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets system to prevent pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of both taps utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its final position.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a rigid seal, triggering the water to penetrate the wall between the bath and the tiling, bring about issues with wetness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked newspaper or soft rope. Remember to always load the bathtub with water before securing, to enable the activity experienced when the bathtub is in usage. The sealant can fracture rather early if you do not consider this movement before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise easily available on the market. It is recommended to fit the tiles making use of waterproof or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like more info about Tools You Need to Install a New Bathtub ? Try leaving feedback directly below. We would be glad to find out your thoughts about this entry. We hope that you visit us again later on. In case you enjoyed our page plz make sure you remember to share it. Thanks a lot for your time spent reading it.
24/7 emergency? We're here! Report this page